From: Christian Heller <c.heller@plomlompom.de>
Date: Wed, 23 Oct 2019 19:30:20 +0000 (+0200)
Subject: Move tlp config file to proper location.
X-Git-Url: https://plomlompom.com/repos/%7B%7B%20web_path%20%7D%7D/%7B%7Bprefix%7D%7D/static/%27%29;%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20chunks.push%28escapeHTML%28span%5B2%5D%29%29;%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20%20chunks.push%28%27?a=commitdiff_plain;h=fe701d694a615861fb80e339f5325aa3092b5989;p=config

Move tlp config file to proper location.
---

diff --git a/buster/etc_files/x200s/etc/default/tlp b/buster/etc_files/x200s/etc/default/tlp
new file mode 100644
index 0000000..b73846b
--- /dev/null
+++ b/buster/etc_files/x200s/etc/default/tlp
@@ -0,0 +1,306 @@
+# ------------------------------------------------------------------------------
+# tlp - Parameters for power saving
+# See full explanation: http://linrunner.de/en/tlp/docs/tlp-configuration.html
+
+# Hint: some features are disabled by default, remove the leading # to enable
+# them.
+
+# Set to 0 to disable, 1 to enable TLP.
+TLP_ENABLE=1
+
+# Operation mode when no power supply can be detected: AC, BAT.
+# Concerns some desktop and embedded hardware only.
+TLP_DEFAULT_MODE=AC
+
+# Operation mode select: 0=depend on power source, 1=always use TLP_DEFAULT_MODE
+# Hint: use in conjunction with TLP_DEFAULT_MODE=BAT for BAT settings on AC.
+TLP_PERSISTENT_DEFAULT=0
+
+# Seconds laptop mode has to wait after the disk goes idle before doing a sync.
+# Non-zero value enables, zero disables laptop mode.
+DISK_IDLE_SECS_ON_AC=0
+DISK_IDLE_SECS_ON_BAT=2
+
+# Dirty page values (timeouts in secs).
+MAX_LOST_WORK_SECS_ON_AC=15
+MAX_LOST_WORK_SECS_ON_BAT=60
+
+# Hint: CPU parameters below are disabled by default, remove the leading #
+# to enable them, otherwise kernel default values are used.
+
+# Select a CPU frequency scaling governor.
+# Intel Core i processor with intel_pstate driver:
+#   powersave(*), performance.
+# Older hardware with acpi-cpufreq driver:
+#   ondemand(*), powersave, performance, conservative, schedutil.
+# (*) is recommended.
+# Hint: use tlp-stat -p to show the active driver and available governors.
+# Important:
+#   powersave for intel_pstate and ondemand for acpi-cpufreq are power
+#   efficient for *almost all* workloads and therefore kernel and most
+#   distributions have chosen them as defaults. If you still want to change,
+#   you should know what you're doing! You *must* disable your distribution's
+#   governor settings or conflicts will occur.
+#CPU_SCALING_GOVERNOR_ON_AC=powersave
+#CPU_SCALING_GOVERNOR_ON_BAT=powersave
+
+# Set the min/max frequency available for the scaling governor.
+# Possible values strongly depend on your CPU. For available frequencies see
+# the output of tlp-stat -p.
+#CPU_SCALING_MIN_FREQ_ON_AC=0
+#CPU_SCALING_MAX_FREQ_ON_AC=0
+#CPU_SCALING_MIN_FREQ_ON_BAT=0
+#CPU_SCALING_MAX_FREQ_ON_BAT=0
+
+# Set energy performance hints (HWP) for Intel P-state governor:
+#   performance, balance_performance, default, balance_power, power
+# Values are given in order of increasing power saving.
+# Note: Intel Skylake or newer CPU and Kernel >= 4.10 required.
+CPU_HWP_ON_AC=balance_performance
+CPU_HWP_ON_BAT=balance_power
+
+# Set Intel P-state performance: 0..100 (%).
+# Limit the max/min P-state to control the power dissipation of the CPU.
+# Values are stated as a percentage of the available performance.
+# Requires an Intel Core i processor with intel_pstate driver.
+#CPU_MIN_PERF_ON_AC=0
+#CPU_MAX_PERF_ON_AC=100
+#CPU_MIN_PERF_ON_BAT=0
+#CPU_MAX_PERF_ON_BAT=30
+
+# Set the CPU "turbo boost" feature: 0=disable, 1=allow
+# Requires an Intel Core i processor.
+# Important:
+# - This may conflict with your distribution's governor settings
+# - A value of 1 does *not* activate boosting, it just allows it
+#CPU_BOOST_ON_AC=1
+#CPU_BOOST_ON_BAT=0
+
+# Minimize number of used CPU cores/hyper-threads under light load conditions:
+#   0=disable, 1=enable.
+SCHED_POWERSAVE_ON_AC=0
+SCHED_POWERSAVE_ON_BAT=1
+
+# Kernel NMI Watchdog:
+#   0=disable (default, saves power), 1=enable (for kernel debugging only).
+NMI_WATCHDOG=0
+
+# Change CPU voltages aka "undervolting" - Kernel with PHC patch required.
+# Frequency voltage pairs are written to:
+#   /sys/devices/system/cpu/cpu0/cpufreq/phc_controls
+# CAUTION: only use this, if you thoroughly understand what you are doing!
+#PHC_CONTROLS="F:V F:V F:V F:V"
+
+# Set CPU performance versus energy savings policy:
+#   performance, balance-performance, default, balance-power, power.
+# Values are given in order of increasing power saving.
+# Requires kernel module msr and x86_energy_perf_policy from linux-tools.
+ENERGY_PERF_POLICY_ON_AC=performance
+ENERGY_PERF_POLICY_ON_BAT=power
+
+# Disk devices; separate multiple devices with spaces (default: sda).
+# Devices can be specified by disk ID also (lookup with: tlp diskid).
+DISK_DEVICES="sda sdb"
+
+# Disk advanced power management level: 1..254, 255 (max saving, min, off).
+# Levels 1..127 may spin down the disk; 255 allowable on most drives.
+# Separate values for multiple disks with spaces. Use the special value 'keep'
+# to keep the hardware default for the particular disk.
+DISK_APM_LEVEL_ON_AC="254 254"
+DISK_APM_LEVEL_ON_BAT="128 128"
+
+# Hard disk spin down timeout:
+#   0:        spin down disabled
+#   1..240:   timeouts from 5s to 20min (in units of 5s)
+#   241..251: timeouts from 30min to 5.5 hours (in units of 30min)
+# See 'man hdparm' for details.
+# Separate values for multiple disks with spaces. Use the special value 'keep'
+# to keep the hardware default for the particular disk.
+#DISK_SPINDOWN_TIMEOUT_ON_AC="0 0"
+#DISK_SPINDOWN_TIMEOUT_ON_BAT="0 0"
+
+# Select IO scheduler for the disk devices: cfq, deadline, noop (Default: cfq).
+# Separate values for multiple disks with spaces. Use the special value 'keep'
+# to keep the kernel default scheduler for the particular disk.
+#DISK_IOSCHED="cfq cfq"
+
+# AHCI link power management (ALPM) for disk devices:
+#   min_power, med_power_with_dipm(*), medium_power, max_performance.
+# (*) Kernel >= 4.15 required, then recommended.
+# Multiple values separated with spaces are tried sequentially until success.
+SATA_LINKPWR_ON_AC="med_power_with_dipm max_performance"
+SATA_LINKPWR_ON_BAT="med_power_with_dipm min_power"
+
+# Exclude host devices from AHCI link power management.
+# Separate multiple hosts with spaces.
+#SATA_LINKPWR_BLACKLIST="host1"
+
+# Runtime Power Management for AHCI host and disks devices:
+#   on=disable, auto=enable.
+# EXPERIMENTAL ** WARNING: auto will most likely cause system lockups/data loss.
+#AHCI_RUNTIME_PM_ON_AC=on
+#AHCI_RUNTIME_PM_ON_BAT=on
+
+# Seconds of inactivity before disk is suspended.
+AHCI_RUNTIME_PM_TIMEOUT=15
+
+# PCI Express Active State Power Management (PCIe ASPM):
+#   default, performance, powersave.
+PCIE_ASPM_ON_AC=performance
+PCIE_ASPM_ON_BAT=powersave
+
+# Radeon graphics clock speed (profile method): low, mid, high, auto, default;
+# auto = mid on BAT, high on AC; default = use hardware defaults.
+RADEON_POWER_PROFILE_ON_AC=high
+RADEON_POWER_PROFILE_ON_BAT=low
+
+# Radeon dynamic power management method (DPM): battery, performance.
+RADEON_DPM_STATE_ON_AC=performance
+RADEON_DPM_STATE_ON_BAT=battery
+
+# Radeon DPM performance level: auto, low, high; auto is recommended.
+RADEON_DPM_PERF_LEVEL_ON_AC=auto
+RADEON_DPM_PERF_LEVEL_ON_BAT=auto
+
+# WiFi power saving mode: on=enable, off=disable; not supported by all adapters.
+WIFI_PWR_ON_AC=off
+WIFI_PWR_ON_BAT=on
+
+# Disable wake on LAN: Y/N.
+WOL_DISABLE=Y
+
+# Enable audio power saving for Intel HDA, AC97 devices (timeout in secs).
+# A value of 0 disables, >=1 enables power saving (recommended: 1).
+SOUND_POWER_SAVE_ON_AC=0
+SOUND_POWER_SAVE_ON_BAT=1
+
+# Disable controller too (HDA only): Y/N.
+SOUND_POWER_SAVE_CONTROLLER=Y
+
+# Power off optical drive in UltraBay/MediaBay: 0=disable, 1=enable.
+# Drive can be powered on again by releasing (and reinserting) the eject lever
+# or by pressing the disc eject button on newer models.
+# Note: an UltraBay/MediaBay hard disk is never powered off.
+BAY_POWEROFF_ON_AC=0
+BAY_POWEROFF_ON_BAT=0
+# Optical drive device to power off (default sr0).
+BAY_DEVICE="sr0"
+
+# Runtime Power Management for PCI(e) bus devices: on=disable, auto=enable.
+RUNTIME_PM_ON_AC=on
+RUNTIME_PM_ON_BAT=auto
+
+# Exclude PCI(e) device adresses the following list from Runtime PM
+# (separate with spaces). Use lspci to get the adresses (1st column).
+#RUNTIME_PM_BLACKLIST="bb:dd.f 11:22.3 44:55.6"
+
+# Exclude PCI(e) devices assigned to the listed drivers from Runtime PM.
+# Default when unconfigured is "amdgpu nouveau nvidia radeon" which
+# prevents accidential power-on of dGPU in hybrid graphics setups.
+# Use "" to disable the feature completely.
+# Separate multiple drivers with spaces.
+#RUNTIME_PM_DRIVER_BLACKLIST="amdgpu nouveau nvidia radeon"
+
+# Set to 0 to disable, 1 to enable USB autosuspend feature.
+USB_AUTOSUSPEND=1
+
+# Exclude listed devices from USB autosuspend (separate with spaces).
+# Use lsusb to get the ids.
+# Note: input devices (usbhid) are excluded automatically
+#USB_BLACKLIST="1111:2222 3333:4444"
+
+# Bluetooth devices are excluded from USB autosuspend:
+#   0=do not exclude, 1=exclude.
+USB_BLACKLIST_BTUSB=0
+
+# Phone devices are excluded from USB autosuspend:
+#   0=do not exclude, 1=exclude (enable charging).
+USB_BLACKLIST_PHONE=0
+
+# Printers are excluded from USB autosuspend:
+#   0=do not exclude, 1=exclude.
+USB_BLACKLIST_PRINTER=1
+
+# WWAN devices are excluded from USB autosuspend:
+#   0=do not exclude, 1=exclude.
+USB_BLACKLIST_WWAN=1
+
+# Include listed devices into USB autosuspend even if already excluded
+# by the blacklists above (separate with spaces).
+# Use lsusb to get the ids.
+#USB_WHITELIST="1111:2222 3333:4444"
+
+# Set to 1 to disable autosuspend before shutdown, 0 to do nothing
+# (workaround for USB devices that cause shutdown problems).
+#USB_AUTOSUSPEND_DISABLE_ON_SHUTDOWN=1
+
+# Restore radio device state (Bluetooth, WiFi, WWAN) from previous shutdown
+# on system startup: 0=disable, 1=enable.
+# Hint: the parameters DEVICES_TO_DISABLE/ENABLE_ON_STARTUP/SHUTDOWN below
+#   are ignored when this is enabled!
+RESTORE_DEVICE_STATE_ON_STARTUP=0
+
+# Radio devices to disable on startup: bluetooth, wifi, wwan.
+# Separate multiple devices with spaces.
+#DEVICES_TO_DISABLE_ON_STARTUP="bluetooth wifi wwan"
+
+# Radio devices to enable on startup: bluetooth, wifi, wwan.
+# Separate multiple devices with spaces.
+#DEVICES_TO_ENABLE_ON_STARTUP="wifi"
+
+# Radio devices to disable on shutdown: bluetooth, wifi, wwan.
+# (workaround for devices that are blocking shutdown).
+#DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth wifi wwan"
+
+# Radio devices to enable on shutdown: bluetooth, wifi, wwan.
+# (to prevent other operating systems from missing radios).
+#DEVICES_TO_ENABLE_ON_SHUTDOWN="wwan"
+
+# Radio devices to enable on AC: bluetooth, wifi, wwan.
+#DEVICES_TO_ENABLE_ON_AC="bluetooth wifi wwan"
+
+# Radio devices to disable on battery: bluetooth, wifi, wwan.
+#DEVICES_TO_DISABLE_ON_BAT="bluetooth wifi wwan"
+
+# Radio devices to disable on battery when not in use (not connected):
+#   bluetooth, wifi, wwan.
+#DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth wifi wwan"
+
+# Battery charge thresholds (ThinkPad only, tp-smapi or acpi-call kernel module
+# required). Charging starts when the remaining capacity falls below the
+# START_CHARGE_THRESH value and stops when exceeding the STOP_CHARGE_THRESH value.
+# Main / Internal battery (values in %)
+START_CHARGE_THRESH_BAT0=75
+STOP_CHARGE_THRESH_BAT0=80
+# Ultrabay / Slice / Replaceable battery (values in %)
+#START_CHARGE_THRESH_BAT1=75
+#STOP_CHARGE_THRESH_BAT1=80
+
+# Restore charge thresholds when AC is unplugged: 0=disable, 1=enable.
+#RESTORE_THRESHOLDS_ON_BAT=1
+
+# ------------------------------------------------------------------------------
+# tlp-rdw - Parameters for the radio device wizard
+# Possible devices: bluetooth, wifi, wwan.
+
+# Hints:
+# - Parameters are disabled by default, remove the leading # to enable them
+# - Separate multiple radio devices with spaces
+
+# Radio devices to disable on connect.
+#DEVICES_TO_DISABLE_ON_LAN_CONNECT="wifi wwan"
+#DEVICES_TO_DISABLE_ON_WIFI_CONNECT="wwan"
+#DEVICES_TO_DISABLE_ON_WWAN_CONNECT="wifi"
+
+# Radio devices to enable on disconnect.
+#DEVICES_TO_ENABLE_ON_LAN_DISCONNECT="wifi wwan"
+#DEVICES_TO_ENABLE_ON_WIFI_DISCONNECT=""
+#DEVICES_TO_ENABLE_ON_WWAN_DISCONNECT=""
+
+# Radio devices to enable/disable when docked.
+#DEVICES_TO_ENABLE_ON_DOCK=""
+#DEVICES_TO_DISABLE_ON_DOCK=""
+
+# Radio devices to enable/disable when undocked.
+#DEVICES_TO_ENABLE_ON_UNDOCK="wifi"
+#DEVICES_TO_DISABLE_ON_UNDOCK=""
diff --git a/buster/etc_files/x200s/etc/tlp b/buster/etc_files/x200s/etc/tlp
deleted file mode 100644
index b73846b..0000000
--- a/buster/etc_files/x200s/etc/tlp
+++ /dev/null
@@ -1,306 +0,0 @@
-# ------------------------------------------------------------------------------
-# tlp - Parameters for power saving
-# See full explanation: http://linrunner.de/en/tlp/docs/tlp-configuration.html
-
-# Hint: some features are disabled by default, remove the leading # to enable
-# them.
-
-# Set to 0 to disable, 1 to enable TLP.
-TLP_ENABLE=1
-
-# Operation mode when no power supply can be detected: AC, BAT.
-# Concerns some desktop and embedded hardware only.
-TLP_DEFAULT_MODE=AC
-
-# Operation mode select: 0=depend on power source, 1=always use TLP_DEFAULT_MODE
-# Hint: use in conjunction with TLP_DEFAULT_MODE=BAT for BAT settings on AC.
-TLP_PERSISTENT_DEFAULT=0
-
-# Seconds laptop mode has to wait after the disk goes idle before doing a sync.
-# Non-zero value enables, zero disables laptop mode.
-DISK_IDLE_SECS_ON_AC=0
-DISK_IDLE_SECS_ON_BAT=2
-
-# Dirty page values (timeouts in secs).
-MAX_LOST_WORK_SECS_ON_AC=15
-MAX_LOST_WORK_SECS_ON_BAT=60
-
-# Hint: CPU parameters below are disabled by default, remove the leading #
-# to enable them, otherwise kernel default values are used.
-
-# Select a CPU frequency scaling governor.
-# Intel Core i processor with intel_pstate driver:
-#   powersave(*), performance.
-# Older hardware with acpi-cpufreq driver:
-#   ondemand(*), powersave, performance, conservative, schedutil.
-# (*) is recommended.
-# Hint: use tlp-stat -p to show the active driver and available governors.
-# Important:
-#   powersave for intel_pstate and ondemand for acpi-cpufreq are power
-#   efficient for *almost all* workloads and therefore kernel and most
-#   distributions have chosen them as defaults. If you still want to change,
-#   you should know what you're doing! You *must* disable your distribution's
-#   governor settings or conflicts will occur.
-#CPU_SCALING_GOVERNOR_ON_AC=powersave
-#CPU_SCALING_GOVERNOR_ON_BAT=powersave
-
-# Set the min/max frequency available for the scaling governor.
-# Possible values strongly depend on your CPU. For available frequencies see
-# the output of tlp-stat -p.
-#CPU_SCALING_MIN_FREQ_ON_AC=0
-#CPU_SCALING_MAX_FREQ_ON_AC=0
-#CPU_SCALING_MIN_FREQ_ON_BAT=0
-#CPU_SCALING_MAX_FREQ_ON_BAT=0
-
-# Set energy performance hints (HWP) for Intel P-state governor:
-#   performance, balance_performance, default, balance_power, power
-# Values are given in order of increasing power saving.
-# Note: Intel Skylake or newer CPU and Kernel >= 4.10 required.
-CPU_HWP_ON_AC=balance_performance
-CPU_HWP_ON_BAT=balance_power
-
-# Set Intel P-state performance: 0..100 (%).
-# Limit the max/min P-state to control the power dissipation of the CPU.
-# Values are stated as a percentage of the available performance.
-# Requires an Intel Core i processor with intel_pstate driver.
-#CPU_MIN_PERF_ON_AC=0
-#CPU_MAX_PERF_ON_AC=100
-#CPU_MIN_PERF_ON_BAT=0
-#CPU_MAX_PERF_ON_BAT=30
-
-# Set the CPU "turbo boost" feature: 0=disable, 1=allow
-# Requires an Intel Core i processor.
-# Important:
-# - This may conflict with your distribution's governor settings
-# - A value of 1 does *not* activate boosting, it just allows it
-#CPU_BOOST_ON_AC=1
-#CPU_BOOST_ON_BAT=0
-
-# Minimize number of used CPU cores/hyper-threads under light load conditions:
-#   0=disable, 1=enable.
-SCHED_POWERSAVE_ON_AC=0
-SCHED_POWERSAVE_ON_BAT=1
-
-# Kernel NMI Watchdog:
-#   0=disable (default, saves power), 1=enable (for kernel debugging only).
-NMI_WATCHDOG=0
-
-# Change CPU voltages aka "undervolting" - Kernel with PHC patch required.
-# Frequency voltage pairs are written to:
-#   /sys/devices/system/cpu/cpu0/cpufreq/phc_controls
-# CAUTION: only use this, if you thoroughly understand what you are doing!
-#PHC_CONTROLS="F:V F:V F:V F:V"
-
-# Set CPU performance versus energy savings policy:
-#   performance, balance-performance, default, balance-power, power.
-# Values are given in order of increasing power saving.
-# Requires kernel module msr and x86_energy_perf_policy from linux-tools.
-ENERGY_PERF_POLICY_ON_AC=performance
-ENERGY_PERF_POLICY_ON_BAT=power
-
-# Disk devices; separate multiple devices with spaces (default: sda).
-# Devices can be specified by disk ID also (lookup with: tlp diskid).
-DISK_DEVICES="sda sdb"
-
-# Disk advanced power management level: 1..254, 255 (max saving, min, off).
-# Levels 1..127 may spin down the disk; 255 allowable on most drives.
-# Separate values for multiple disks with spaces. Use the special value 'keep'
-# to keep the hardware default for the particular disk.
-DISK_APM_LEVEL_ON_AC="254 254"
-DISK_APM_LEVEL_ON_BAT="128 128"
-
-# Hard disk spin down timeout:
-#   0:        spin down disabled
-#   1..240:   timeouts from 5s to 20min (in units of 5s)
-#   241..251: timeouts from 30min to 5.5 hours (in units of 30min)
-# See 'man hdparm' for details.
-# Separate values for multiple disks with spaces. Use the special value 'keep'
-# to keep the hardware default for the particular disk.
-#DISK_SPINDOWN_TIMEOUT_ON_AC="0 0"
-#DISK_SPINDOWN_TIMEOUT_ON_BAT="0 0"
-
-# Select IO scheduler for the disk devices: cfq, deadline, noop (Default: cfq).
-# Separate values for multiple disks with spaces. Use the special value 'keep'
-# to keep the kernel default scheduler for the particular disk.
-#DISK_IOSCHED="cfq cfq"
-
-# AHCI link power management (ALPM) for disk devices:
-#   min_power, med_power_with_dipm(*), medium_power, max_performance.
-# (*) Kernel >= 4.15 required, then recommended.
-# Multiple values separated with spaces are tried sequentially until success.
-SATA_LINKPWR_ON_AC="med_power_with_dipm max_performance"
-SATA_LINKPWR_ON_BAT="med_power_with_dipm min_power"
-
-# Exclude host devices from AHCI link power management.
-# Separate multiple hosts with spaces.
-#SATA_LINKPWR_BLACKLIST="host1"
-
-# Runtime Power Management for AHCI host and disks devices:
-#   on=disable, auto=enable.
-# EXPERIMENTAL ** WARNING: auto will most likely cause system lockups/data loss.
-#AHCI_RUNTIME_PM_ON_AC=on
-#AHCI_RUNTIME_PM_ON_BAT=on
-
-# Seconds of inactivity before disk is suspended.
-AHCI_RUNTIME_PM_TIMEOUT=15
-
-# PCI Express Active State Power Management (PCIe ASPM):
-#   default, performance, powersave.
-PCIE_ASPM_ON_AC=performance
-PCIE_ASPM_ON_BAT=powersave
-
-# Radeon graphics clock speed (profile method): low, mid, high, auto, default;
-# auto = mid on BAT, high on AC; default = use hardware defaults.
-RADEON_POWER_PROFILE_ON_AC=high
-RADEON_POWER_PROFILE_ON_BAT=low
-
-# Radeon dynamic power management method (DPM): battery, performance.
-RADEON_DPM_STATE_ON_AC=performance
-RADEON_DPM_STATE_ON_BAT=battery
-
-# Radeon DPM performance level: auto, low, high; auto is recommended.
-RADEON_DPM_PERF_LEVEL_ON_AC=auto
-RADEON_DPM_PERF_LEVEL_ON_BAT=auto
-
-# WiFi power saving mode: on=enable, off=disable; not supported by all adapters.
-WIFI_PWR_ON_AC=off
-WIFI_PWR_ON_BAT=on
-
-# Disable wake on LAN: Y/N.
-WOL_DISABLE=Y
-
-# Enable audio power saving for Intel HDA, AC97 devices (timeout in secs).
-# A value of 0 disables, >=1 enables power saving (recommended: 1).
-SOUND_POWER_SAVE_ON_AC=0
-SOUND_POWER_SAVE_ON_BAT=1
-
-# Disable controller too (HDA only): Y/N.
-SOUND_POWER_SAVE_CONTROLLER=Y
-
-# Power off optical drive in UltraBay/MediaBay: 0=disable, 1=enable.
-# Drive can be powered on again by releasing (and reinserting) the eject lever
-# or by pressing the disc eject button on newer models.
-# Note: an UltraBay/MediaBay hard disk is never powered off.
-BAY_POWEROFF_ON_AC=0
-BAY_POWEROFF_ON_BAT=0
-# Optical drive device to power off (default sr0).
-BAY_DEVICE="sr0"
-
-# Runtime Power Management for PCI(e) bus devices: on=disable, auto=enable.
-RUNTIME_PM_ON_AC=on
-RUNTIME_PM_ON_BAT=auto
-
-# Exclude PCI(e) device adresses the following list from Runtime PM
-# (separate with spaces). Use lspci to get the adresses (1st column).
-#RUNTIME_PM_BLACKLIST="bb:dd.f 11:22.3 44:55.6"
-
-# Exclude PCI(e) devices assigned to the listed drivers from Runtime PM.
-# Default when unconfigured is "amdgpu nouveau nvidia radeon" which
-# prevents accidential power-on of dGPU in hybrid graphics setups.
-# Use "" to disable the feature completely.
-# Separate multiple drivers with spaces.
-#RUNTIME_PM_DRIVER_BLACKLIST="amdgpu nouveau nvidia radeon"
-
-# Set to 0 to disable, 1 to enable USB autosuspend feature.
-USB_AUTOSUSPEND=1
-
-# Exclude listed devices from USB autosuspend (separate with spaces).
-# Use lsusb to get the ids.
-# Note: input devices (usbhid) are excluded automatically
-#USB_BLACKLIST="1111:2222 3333:4444"
-
-# Bluetooth devices are excluded from USB autosuspend:
-#   0=do not exclude, 1=exclude.
-USB_BLACKLIST_BTUSB=0
-
-# Phone devices are excluded from USB autosuspend:
-#   0=do not exclude, 1=exclude (enable charging).
-USB_BLACKLIST_PHONE=0
-
-# Printers are excluded from USB autosuspend:
-#   0=do not exclude, 1=exclude.
-USB_BLACKLIST_PRINTER=1
-
-# WWAN devices are excluded from USB autosuspend:
-#   0=do not exclude, 1=exclude.
-USB_BLACKLIST_WWAN=1
-
-# Include listed devices into USB autosuspend even if already excluded
-# by the blacklists above (separate with spaces).
-# Use lsusb to get the ids.
-#USB_WHITELIST="1111:2222 3333:4444"
-
-# Set to 1 to disable autosuspend before shutdown, 0 to do nothing
-# (workaround for USB devices that cause shutdown problems).
-#USB_AUTOSUSPEND_DISABLE_ON_SHUTDOWN=1
-
-# Restore radio device state (Bluetooth, WiFi, WWAN) from previous shutdown
-# on system startup: 0=disable, 1=enable.
-# Hint: the parameters DEVICES_TO_DISABLE/ENABLE_ON_STARTUP/SHUTDOWN below
-#   are ignored when this is enabled!
-RESTORE_DEVICE_STATE_ON_STARTUP=0
-
-# Radio devices to disable on startup: bluetooth, wifi, wwan.
-# Separate multiple devices with spaces.
-#DEVICES_TO_DISABLE_ON_STARTUP="bluetooth wifi wwan"
-
-# Radio devices to enable on startup: bluetooth, wifi, wwan.
-# Separate multiple devices with spaces.
-#DEVICES_TO_ENABLE_ON_STARTUP="wifi"
-
-# Radio devices to disable on shutdown: bluetooth, wifi, wwan.
-# (workaround for devices that are blocking shutdown).
-#DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth wifi wwan"
-
-# Radio devices to enable on shutdown: bluetooth, wifi, wwan.
-# (to prevent other operating systems from missing radios).
-#DEVICES_TO_ENABLE_ON_SHUTDOWN="wwan"
-
-# Radio devices to enable on AC: bluetooth, wifi, wwan.
-#DEVICES_TO_ENABLE_ON_AC="bluetooth wifi wwan"
-
-# Radio devices to disable on battery: bluetooth, wifi, wwan.
-#DEVICES_TO_DISABLE_ON_BAT="bluetooth wifi wwan"
-
-# Radio devices to disable on battery when not in use (not connected):
-#   bluetooth, wifi, wwan.
-#DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth wifi wwan"
-
-# Battery charge thresholds (ThinkPad only, tp-smapi or acpi-call kernel module
-# required). Charging starts when the remaining capacity falls below the
-# START_CHARGE_THRESH value and stops when exceeding the STOP_CHARGE_THRESH value.
-# Main / Internal battery (values in %)
-START_CHARGE_THRESH_BAT0=75
-STOP_CHARGE_THRESH_BAT0=80
-# Ultrabay / Slice / Replaceable battery (values in %)
-#START_CHARGE_THRESH_BAT1=75
-#STOP_CHARGE_THRESH_BAT1=80
-
-# Restore charge thresholds when AC is unplugged: 0=disable, 1=enable.
-#RESTORE_THRESHOLDS_ON_BAT=1
-
-# ------------------------------------------------------------------------------
-# tlp-rdw - Parameters for the radio device wizard
-# Possible devices: bluetooth, wifi, wwan.
-
-# Hints:
-# - Parameters are disabled by default, remove the leading # to enable them
-# - Separate multiple radio devices with spaces
-
-# Radio devices to disable on connect.
-#DEVICES_TO_DISABLE_ON_LAN_CONNECT="wifi wwan"
-#DEVICES_TO_DISABLE_ON_WIFI_CONNECT="wwan"
-#DEVICES_TO_DISABLE_ON_WWAN_CONNECT="wifi"
-
-# Radio devices to enable on disconnect.
-#DEVICES_TO_ENABLE_ON_LAN_DISCONNECT="wifi wwan"
-#DEVICES_TO_ENABLE_ON_WIFI_DISCONNECT=""
-#DEVICES_TO_ENABLE_ON_WWAN_DISCONNECT=""
-
-# Radio devices to enable/disable when docked.
-#DEVICES_TO_ENABLE_ON_DOCK=""
-#DEVICES_TO_DISABLE_ON_DOCK=""
-
-# Radio devices to enable/disable when undocked.
-#DEVICES_TO_ENABLE_ON_UNDOCK="wifi"
-#DEVICES_TO_DISABLE_ON_UNDOCK=""