From: Christian Heller Date: Wed, 14 Aug 2019 22:13:16 +0000 (+0200) Subject: Add TLP. X-Git-Url: https://plomlompom.com/repos/%7B%7B%20web_path%20%7D%7D/decks/%7B%7Bdb.prefix%7D%7D/static/blog?a=commitdiff_plain;h=1dc43c0723db724ccda299dd644c05528dd15ef2;p=config Add TLP. --- diff --git a/buster/apt-mark/x200s b/buster/apt-mark/x200s index d06ad3f..6a780f2 100644 --- a/buster/apt-mark/x200s +++ b/buster/apt-mark/x200s @@ -1,3 +1,7 @@ # for wifi firmware-iwlwifi +# for tlp +tlp +tp-smapi-dkms +linux-headers-amd64 # diff --git a/buster/etc_files/x200s/etc/tlp b/buster/etc_files/x200s/etc/tlp new file mode 100644 index 0000000..b73846b --- /dev/null +++ b/buster/etc_files/x200s/etc/tlp @@ -0,0 +1,306 @@ +# ------------------------------------------------------------------------------ +# tlp - Parameters for power saving +# See full explanation: http://linrunner.de/en/tlp/docs/tlp-configuration.html + +# Hint: some features are disabled by default, remove the leading # to enable +# them. + +# Set to 0 to disable, 1 to enable TLP. +TLP_ENABLE=1 + +# Operation mode when no power supply can be detected: AC, BAT. +# Concerns some desktop and embedded hardware only. +TLP_DEFAULT_MODE=AC + +# Operation mode select: 0=depend on power source, 1=always use TLP_DEFAULT_MODE +# Hint: use in conjunction with TLP_DEFAULT_MODE=BAT for BAT settings on AC. +TLP_PERSISTENT_DEFAULT=0 + +# Seconds laptop mode has to wait after the disk goes idle before doing a sync. +# Non-zero value enables, zero disables laptop mode. +DISK_IDLE_SECS_ON_AC=0 +DISK_IDLE_SECS_ON_BAT=2 + +# Dirty page values (timeouts in secs). +MAX_LOST_WORK_SECS_ON_AC=15 +MAX_LOST_WORK_SECS_ON_BAT=60 + +# Hint: CPU parameters below are disabled by default, remove the leading # +# to enable them, otherwise kernel default values are used. + +# Select a CPU frequency scaling governor. +# Intel Core i processor with intel_pstate driver: +# powersave(*), performance. +# Older hardware with acpi-cpufreq driver: +# ondemand(*), powersave, performance, conservative, schedutil. +# (*) is recommended. +# Hint: use tlp-stat -p to show the active driver and available governors. +# Important: +# powersave for intel_pstate and ondemand for acpi-cpufreq are power +# efficient for *almost all* workloads and therefore kernel and most +# distributions have chosen them as defaults. If you still want to change, +# you should know what you're doing! You *must* disable your distribution's +# governor settings or conflicts will occur. +#CPU_SCALING_GOVERNOR_ON_AC=powersave +#CPU_SCALING_GOVERNOR_ON_BAT=powersave + +# Set the min/max frequency available for the scaling governor. +# Possible values strongly depend on your CPU. For available frequencies see +# the output of tlp-stat -p. +#CPU_SCALING_MIN_FREQ_ON_AC=0 +#CPU_SCALING_MAX_FREQ_ON_AC=0 +#CPU_SCALING_MIN_FREQ_ON_BAT=0 +#CPU_SCALING_MAX_FREQ_ON_BAT=0 + +# Set energy performance hints (HWP) for Intel P-state governor: +# performance, balance_performance, default, balance_power, power +# Values are given in order of increasing power saving. +# Note: Intel Skylake or newer CPU and Kernel >= 4.10 required. +CPU_HWP_ON_AC=balance_performance +CPU_HWP_ON_BAT=balance_power + +# Set Intel P-state performance: 0..100 (%). +# Limit the max/min P-state to control the power dissipation of the CPU. +# Values are stated as a percentage of the available performance. +# Requires an Intel Core i processor with intel_pstate driver. +#CPU_MIN_PERF_ON_AC=0 +#CPU_MAX_PERF_ON_AC=100 +#CPU_MIN_PERF_ON_BAT=0 +#CPU_MAX_PERF_ON_BAT=30 + +# Set the CPU "turbo boost" feature: 0=disable, 1=allow +# Requires an Intel Core i processor. +# Important: +# - This may conflict with your distribution's governor settings +# - A value of 1 does *not* activate boosting, it just allows it +#CPU_BOOST_ON_AC=1 +#CPU_BOOST_ON_BAT=0 + +# Minimize number of used CPU cores/hyper-threads under light load conditions: +# 0=disable, 1=enable. +SCHED_POWERSAVE_ON_AC=0 +SCHED_POWERSAVE_ON_BAT=1 + +# Kernel NMI Watchdog: +# 0=disable (default, saves power), 1=enable (for kernel debugging only). +NMI_WATCHDOG=0 + +# Change CPU voltages aka "undervolting" - Kernel with PHC patch required. +# Frequency voltage pairs are written to: +# /sys/devices/system/cpu/cpu0/cpufreq/phc_controls +# CAUTION: only use this, if you thoroughly understand what you are doing! +#PHC_CONTROLS="F:V F:V F:V F:V" + +# Set CPU performance versus energy savings policy: +# performance, balance-performance, default, balance-power, power. +# Values are given in order of increasing power saving. +# Requires kernel module msr and x86_energy_perf_policy from linux-tools. +ENERGY_PERF_POLICY_ON_AC=performance +ENERGY_PERF_POLICY_ON_BAT=power + +# Disk devices; separate multiple devices with spaces (default: sda). +# Devices can be specified by disk ID also (lookup with: tlp diskid). +DISK_DEVICES="sda sdb" + +# Disk advanced power management level: 1..254, 255 (max saving, min, off). +# Levels 1..127 may spin down the disk; 255 allowable on most drives. +# Separate values for multiple disks with spaces. Use the special value 'keep' +# to keep the hardware default for the particular disk. +DISK_APM_LEVEL_ON_AC="254 254" +DISK_APM_LEVEL_ON_BAT="128 128" + +# Hard disk spin down timeout: +# 0: spin down disabled +# 1..240: timeouts from 5s to 20min (in units of 5s) +# 241..251: timeouts from 30min to 5.5 hours (in units of 30min) +# See 'man hdparm' for details. +# Separate values for multiple disks with spaces. Use the special value 'keep' +# to keep the hardware default for the particular disk. +#DISK_SPINDOWN_TIMEOUT_ON_AC="0 0" +#DISK_SPINDOWN_TIMEOUT_ON_BAT="0 0" + +# Select IO scheduler for the disk devices: cfq, deadline, noop (Default: cfq). +# Separate values for multiple disks with spaces. Use the special value 'keep' +# to keep the kernel default scheduler for the particular disk. +#DISK_IOSCHED="cfq cfq" + +# AHCI link power management (ALPM) for disk devices: +# min_power, med_power_with_dipm(*), medium_power, max_performance. +# (*) Kernel >= 4.15 required, then recommended. +# Multiple values separated with spaces are tried sequentially until success. +SATA_LINKPWR_ON_AC="med_power_with_dipm max_performance" +SATA_LINKPWR_ON_BAT="med_power_with_dipm min_power" + +# Exclude host devices from AHCI link power management. +# Separate multiple hosts with spaces. +#SATA_LINKPWR_BLACKLIST="host1" + +# Runtime Power Management for AHCI host and disks devices: +# on=disable, auto=enable. +# EXPERIMENTAL ** WARNING: auto will most likely cause system lockups/data loss. +#AHCI_RUNTIME_PM_ON_AC=on +#AHCI_RUNTIME_PM_ON_BAT=on + +# Seconds of inactivity before disk is suspended. +AHCI_RUNTIME_PM_TIMEOUT=15 + +# PCI Express Active State Power Management (PCIe ASPM): +# default, performance, powersave. +PCIE_ASPM_ON_AC=performance +PCIE_ASPM_ON_BAT=powersave + +# Radeon graphics clock speed (profile method): low, mid, high, auto, default; +# auto = mid on BAT, high on AC; default = use hardware defaults. +RADEON_POWER_PROFILE_ON_AC=high +RADEON_POWER_PROFILE_ON_BAT=low + +# Radeon dynamic power management method (DPM): battery, performance. +RADEON_DPM_STATE_ON_AC=performance +RADEON_DPM_STATE_ON_BAT=battery + +# Radeon DPM performance level: auto, low, high; auto is recommended. +RADEON_DPM_PERF_LEVEL_ON_AC=auto +RADEON_DPM_PERF_LEVEL_ON_BAT=auto + +# WiFi power saving mode: on=enable, off=disable; not supported by all adapters. +WIFI_PWR_ON_AC=off +WIFI_PWR_ON_BAT=on + +# Disable wake on LAN: Y/N. +WOL_DISABLE=Y + +# Enable audio power saving for Intel HDA, AC97 devices (timeout in secs). +# A value of 0 disables, >=1 enables power saving (recommended: 1). +SOUND_POWER_SAVE_ON_AC=0 +SOUND_POWER_SAVE_ON_BAT=1 + +# Disable controller too (HDA only): Y/N. +SOUND_POWER_SAVE_CONTROLLER=Y + +# Power off optical drive in UltraBay/MediaBay: 0=disable, 1=enable. +# Drive can be powered on again by releasing (and reinserting) the eject lever +# or by pressing the disc eject button on newer models. +# Note: an UltraBay/MediaBay hard disk is never powered off. +BAY_POWEROFF_ON_AC=0 +BAY_POWEROFF_ON_BAT=0 +# Optical drive device to power off (default sr0). +BAY_DEVICE="sr0" + +# Runtime Power Management for PCI(e) bus devices: on=disable, auto=enable. +RUNTIME_PM_ON_AC=on +RUNTIME_PM_ON_BAT=auto + +# Exclude PCI(e) device adresses the following list from Runtime PM +# (separate with spaces). Use lspci to get the adresses (1st column). +#RUNTIME_PM_BLACKLIST="bb:dd.f 11:22.3 44:55.6" + +# Exclude PCI(e) devices assigned to the listed drivers from Runtime PM. +# Default when unconfigured is "amdgpu nouveau nvidia radeon" which +# prevents accidential power-on of dGPU in hybrid graphics setups. +# Use "" to disable the feature completely. +# Separate multiple drivers with spaces. +#RUNTIME_PM_DRIVER_BLACKLIST="amdgpu nouveau nvidia radeon" + +# Set to 0 to disable, 1 to enable USB autosuspend feature. +USB_AUTOSUSPEND=1 + +# Exclude listed devices from USB autosuspend (separate with spaces). +# Use lsusb to get the ids. +# Note: input devices (usbhid) are excluded automatically +#USB_BLACKLIST="1111:2222 3333:4444" + +# Bluetooth devices are excluded from USB autosuspend: +# 0=do not exclude, 1=exclude. +USB_BLACKLIST_BTUSB=0 + +# Phone devices are excluded from USB autosuspend: +# 0=do not exclude, 1=exclude (enable charging). +USB_BLACKLIST_PHONE=0 + +# Printers are excluded from USB autosuspend: +# 0=do not exclude, 1=exclude. +USB_BLACKLIST_PRINTER=1 + +# WWAN devices are excluded from USB autosuspend: +# 0=do not exclude, 1=exclude. +USB_BLACKLIST_WWAN=1 + +# Include listed devices into USB autosuspend even if already excluded +# by the blacklists above (separate with spaces). +# Use lsusb to get the ids. +#USB_WHITELIST="1111:2222 3333:4444" + +# Set to 1 to disable autosuspend before shutdown, 0 to do nothing +# (workaround for USB devices that cause shutdown problems). +#USB_AUTOSUSPEND_DISABLE_ON_SHUTDOWN=1 + +# Restore radio device state (Bluetooth, WiFi, WWAN) from previous shutdown +# on system startup: 0=disable, 1=enable. +# Hint: the parameters DEVICES_TO_DISABLE/ENABLE_ON_STARTUP/SHUTDOWN below +# are ignored when this is enabled! +RESTORE_DEVICE_STATE_ON_STARTUP=0 + +# Radio devices to disable on startup: bluetooth, wifi, wwan. +# Separate multiple devices with spaces. +#DEVICES_TO_DISABLE_ON_STARTUP="bluetooth wifi wwan" + +# Radio devices to enable on startup: bluetooth, wifi, wwan. +# Separate multiple devices with spaces. +#DEVICES_TO_ENABLE_ON_STARTUP="wifi" + +# Radio devices to disable on shutdown: bluetooth, wifi, wwan. +# (workaround for devices that are blocking shutdown). +#DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth wifi wwan" + +# Radio devices to enable on shutdown: bluetooth, wifi, wwan. +# (to prevent other operating systems from missing radios). +#DEVICES_TO_ENABLE_ON_SHUTDOWN="wwan" + +# Radio devices to enable on AC: bluetooth, wifi, wwan. +#DEVICES_TO_ENABLE_ON_AC="bluetooth wifi wwan" + +# Radio devices to disable on battery: bluetooth, wifi, wwan. +#DEVICES_TO_DISABLE_ON_BAT="bluetooth wifi wwan" + +# Radio devices to disable on battery when not in use (not connected): +# bluetooth, wifi, wwan. +#DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth wifi wwan" + +# Battery charge thresholds (ThinkPad only, tp-smapi or acpi-call kernel module +# required). Charging starts when the remaining capacity falls below the +# START_CHARGE_THRESH value and stops when exceeding the STOP_CHARGE_THRESH value. +# Main / Internal battery (values in %) +START_CHARGE_THRESH_BAT0=75 +STOP_CHARGE_THRESH_BAT0=80 +# Ultrabay / Slice / Replaceable battery (values in %) +#START_CHARGE_THRESH_BAT1=75 +#STOP_CHARGE_THRESH_BAT1=80 + +# Restore charge thresholds when AC is unplugged: 0=disable, 1=enable. +#RESTORE_THRESHOLDS_ON_BAT=1 + +# ------------------------------------------------------------------------------ +# tlp-rdw - Parameters for the radio device wizard +# Possible devices: bluetooth, wifi, wwan. + +# Hints: +# - Parameters are disabled by default, remove the leading # to enable them +# - Separate multiple radio devices with spaces + +# Radio devices to disable on connect. +#DEVICES_TO_DISABLE_ON_LAN_CONNECT="wifi wwan" +#DEVICES_TO_DISABLE_ON_WIFI_CONNECT="wwan" +#DEVICES_TO_DISABLE_ON_WWAN_CONNECT="wifi" + +# Radio devices to enable on disconnect. +#DEVICES_TO_ENABLE_ON_LAN_DISCONNECT="wifi wwan" +#DEVICES_TO_ENABLE_ON_WIFI_DISCONNECT="" +#DEVICES_TO_ENABLE_ON_WWAN_DISCONNECT="" + +# Radio devices to enable/disable when docked. +#DEVICES_TO_ENABLE_ON_DOCK="" +#DEVICES_TO_DISABLE_ON_DOCK="" + +# Radio devices to enable/disable when undocked. +#DEVICES_TO_ENABLE_ON_UNDOCK="wifi" +#DEVICES_TO_DISABLE_ON_UNDOCK="" diff --git a/buster/setup_scripts/setup_home.sh b/buster/setup_scripts/setup_home.sh index e6abd78..4bd06ef 100755 --- a/buster/setup_scripts/setup_home.sh +++ b/buster/setup_scripts/setup_home.sh @@ -98,4 +98,4 @@ if [ -f "${HOME}/${authinfo_file}" ]; then fi # Final note on how to integrate tridactyl. -echo "TODO: As tridactyl user, don't forget to do :source on the first Firefox run and then re-start." +echo "TODO: As tridactyl user, don't forget to do :source on the first Firefox run, wait a little while (Tridactyl needs to walk through all commands in the .tridactylrc) and then re-start."