From: Christian Heller Date: Wed, 23 Oct 2019 19:30:20 +0000 (+0200) Subject: Move tlp config file to proper location. X-Git-Url: https://plomlompom.com/repos/conditions?a=commitdiff_plain;h=fe701d694a615861fb80e339f5325aa3092b5989;p=config Move tlp config file to proper location. --- diff --git a/buster/etc_files/x200s/etc/default/tlp b/buster/etc_files/x200s/etc/default/tlp new file mode 100644 index 0000000..b73846b --- /dev/null +++ b/buster/etc_files/x200s/etc/default/tlp @@ -0,0 +1,306 @@ +# ------------------------------------------------------------------------------ +# tlp - Parameters for power saving +# See full explanation: http://linrunner.de/en/tlp/docs/tlp-configuration.html + +# Hint: some features are disabled by default, remove the leading # to enable +# them. + +# Set to 0 to disable, 1 to enable TLP. +TLP_ENABLE=1 + +# Operation mode when no power supply can be detected: AC, BAT. +# Concerns some desktop and embedded hardware only. +TLP_DEFAULT_MODE=AC + +# Operation mode select: 0=depend on power source, 1=always use TLP_DEFAULT_MODE +# Hint: use in conjunction with TLP_DEFAULT_MODE=BAT for BAT settings on AC. +TLP_PERSISTENT_DEFAULT=0 + +# Seconds laptop mode has to wait after the disk goes idle before doing a sync. +# Non-zero value enables, zero disables laptop mode. +DISK_IDLE_SECS_ON_AC=0 +DISK_IDLE_SECS_ON_BAT=2 + +# Dirty page values (timeouts in secs). +MAX_LOST_WORK_SECS_ON_AC=15 +MAX_LOST_WORK_SECS_ON_BAT=60 + +# Hint: CPU parameters below are disabled by default, remove the leading # +# to enable them, otherwise kernel default values are used. + +# Select a CPU frequency scaling governor. +# Intel Core i processor with intel_pstate driver: +# powersave(*), performance. +# Older hardware with acpi-cpufreq driver: +# ondemand(*), powersave, performance, conservative, schedutil. +# (*) is recommended. +# Hint: use tlp-stat -p to show the active driver and available governors. +# Important: +# powersave for intel_pstate and ondemand for acpi-cpufreq are power +# efficient for *almost all* workloads and therefore kernel and most +# distributions have chosen them as defaults. If you still want to change, +# you should know what you're doing! You *must* disable your distribution's +# governor settings or conflicts will occur. +#CPU_SCALING_GOVERNOR_ON_AC=powersave +#CPU_SCALING_GOVERNOR_ON_BAT=powersave + +# Set the min/max frequency available for the scaling governor. +# Possible values strongly depend on your CPU. For available frequencies see +# the output of tlp-stat -p. +#CPU_SCALING_MIN_FREQ_ON_AC=0 +#CPU_SCALING_MAX_FREQ_ON_AC=0 +#CPU_SCALING_MIN_FREQ_ON_BAT=0 +#CPU_SCALING_MAX_FREQ_ON_BAT=0 + +# Set energy performance hints (HWP) for Intel P-state governor: +# performance, balance_performance, default, balance_power, power +# Values are given in order of increasing power saving. +# Note: Intel Skylake or newer CPU and Kernel >= 4.10 required. +CPU_HWP_ON_AC=balance_performance +CPU_HWP_ON_BAT=balance_power + +# Set Intel P-state performance: 0..100 (%). +# Limit the max/min P-state to control the power dissipation of the CPU. +# Values are stated as a percentage of the available performance. +# Requires an Intel Core i processor with intel_pstate driver. +#CPU_MIN_PERF_ON_AC=0 +#CPU_MAX_PERF_ON_AC=100 +#CPU_MIN_PERF_ON_BAT=0 +#CPU_MAX_PERF_ON_BAT=30 + +# Set the CPU "turbo boost" feature: 0=disable, 1=allow +# Requires an Intel Core i processor. +# Important: +# - This may conflict with your distribution's governor settings +# - A value of 1 does *not* activate boosting, it just allows it +#CPU_BOOST_ON_AC=1 +#CPU_BOOST_ON_BAT=0 + +# Minimize number of used CPU cores/hyper-threads under light load conditions: +# 0=disable, 1=enable. +SCHED_POWERSAVE_ON_AC=0 +SCHED_POWERSAVE_ON_BAT=1 + +# Kernel NMI Watchdog: +# 0=disable (default, saves power), 1=enable (for kernel debugging only). +NMI_WATCHDOG=0 + +# Change CPU voltages aka "undervolting" - Kernel with PHC patch required. +# Frequency voltage pairs are written to: +# /sys/devices/system/cpu/cpu0/cpufreq/phc_controls +# CAUTION: only use this, if you thoroughly understand what you are doing! +#PHC_CONTROLS="F:V F:V F:V F:V" + +# Set CPU performance versus energy savings policy: +# performance, balance-performance, default, balance-power, power. +# Values are given in order of increasing power saving. +# Requires kernel module msr and x86_energy_perf_policy from linux-tools. +ENERGY_PERF_POLICY_ON_AC=performance +ENERGY_PERF_POLICY_ON_BAT=power + +# Disk devices; separate multiple devices with spaces (default: sda). +# Devices can be specified by disk ID also (lookup with: tlp diskid). +DISK_DEVICES="sda sdb" + +# Disk advanced power management level: 1..254, 255 (max saving, min, off). +# Levels 1..127 may spin down the disk; 255 allowable on most drives. +# Separate values for multiple disks with spaces. Use the special value 'keep' +# to keep the hardware default for the particular disk. +DISK_APM_LEVEL_ON_AC="254 254" +DISK_APM_LEVEL_ON_BAT="128 128" + +# Hard disk spin down timeout: +# 0: spin down disabled +# 1..240: timeouts from 5s to 20min (in units of 5s) +# 241..251: timeouts from 30min to 5.5 hours (in units of 30min) +# See 'man hdparm' for details. +# Separate values for multiple disks with spaces. Use the special value 'keep' +# to keep the hardware default for the particular disk. +#DISK_SPINDOWN_TIMEOUT_ON_AC="0 0" +#DISK_SPINDOWN_TIMEOUT_ON_BAT="0 0" + +# Select IO scheduler for the disk devices: cfq, deadline, noop (Default: cfq). +# Separate values for multiple disks with spaces. Use the special value 'keep' +# to keep the kernel default scheduler for the particular disk. +#DISK_IOSCHED="cfq cfq" + +# AHCI link power management (ALPM) for disk devices: +# min_power, med_power_with_dipm(*), medium_power, max_performance. +# (*) Kernel >= 4.15 required, then recommended. +# Multiple values separated with spaces are tried sequentially until success. +SATA_LINKPWR_ON_AC="med_power_with_dipm max_performance" +SATA_LINKPWR_ON_BAT="med_power_with_dipm min_power" + +# Exclude host devices from AHCI link power management. +# Separate multiple hosts with spaces. +#SATA_LINKPWR_BLACKLIST="host1" + +# Runtime Power Management for AHCI host and disks devices: +# on=disable, auto=enable. +# EXPERIMENTAL ** WARNING: auto will most likely cause system lockups/data loss. +#AHCI_RUNTIME_PM_ON_AC=on +#AHCI_RUNTIME_PM_ON_BAT=on + +# Seconds of inactivity before disk is suspended. +AHCI_RUNTIME_PM_TIMEOUT=15 + +# PCI Express Active State Power Management (PCIe ASPM): +# default, performance, powersave. +PCIE_ASPM_ON_AC=performance +PCIE_ASPM_ON_BAT=powersave + +# Radeon graphics clock speed (profile method): low, mid, high, auto, default; +# auto = mid on BAT, high on AC; default = use hardware defaults. +RADEON_POWER_PROFILE_ON_AC=high +RADEON_POWER_PROFILE_ON_BAT=low + +# Radeon dynamic power management method (DPM): battery, performance. +RADEON_DPM_STATE_ON_AC=performance +RADEON_DPM_STATE_ON_BAT=battery + +# Radeon DPM performance level: auto, low, high; auto is recommended. +RADEON_DPM_PERF_LEVEL_ON_AC=auto +RADEON_DPM_PERF_LEVEL_ON_BAT=auto + +# WiFi power saving mode: on=enable, off=disable; not supported by all adapters. +WIFI_PWR_ON_AC=off +WIFI_PWR_ON_BAT=on + +# Disable wake on LAN: Y/N. +WOL_DISABLE=Y + +# Enable audio power saving for Intel HDA, AC97 devices (timeout in secs). +# A value of 0 disables, >=1 enables power saving (recommended: 1). +SOUND_POWER_SAVE_ON_AC=0 +SOUND_POWER_SAVE_ON_BAT=1 + +# Disable controller too (HDA only): Y/N. +SOUND_POWER_SAVE_CONTROLLER=Y + +# Power off optical drive in UltraBay/MediaBay: 0=disable, 1=enable. +# Drive can be powered on again by releasing (and reinserting) the eject lever +# or by pressing the disc eject button on newer models. +# Note: an UltraBay/MediaBay hard disk is never powered off. +BAY_POWEROFF_ON_AC=0 +BAY_POWEROFF_ON_BAT=0 +# Optical drive device to power off (default sr0). +BAY_DEVICE="sr0" + +# Runtime Power Management for PCI(e) bus devices: on=disable, auto=enable. +RUNTIME_PM_ON_AC=on +RUNTIME_PM_ON_BAT=auto + +# Exclude PCI(e) device adresses the following list from Runtime PM +# (separate with spaces). Use lspci to get the adresses (1st column). +#RUNTIME_PM_BLACKLIST="bb:dd.f 11:22.3 44:55.6" + +# Exclude PCI(e) devices assigned to the listed drivers from Runtime PM. +# Default when unconfigured is "amdgpu nouveau nvidia radeon" which +# prevents accidential power-on of dGPU in hybrid graphics setups. +# Use "" to disable the feature completely. +# Separate multiple drivers with spaces. +#RUNTIME_PM_DRIVER_BLACKLIST="amdgpu nouveau nvidia radeon" + +# Set to 0 to disable, 1 to enable USB autosuspend feature. +USB_AUTOSUSPEND=1 + +# Exclude listed devices from USB autosuspend (separate with spaces). +# Use lsusb to get the ids. +# Note: input devices (usbhid) are excluded automatically +#USB_BLACKLIST="1111:2222 3333:4444" + +# Bluetooth devices are excluded from USB autosuspend: +# 0=do not exclude, 1=exclude. +USB_BLACKLIST_BTUSB=0 + +# Phone devices are excluded from USB autosuspend: +# 0=do not exclude, 1=exclude (enable charging). +USB_BLACKLIST_PHONE=0 + +# Printers are excluded from USB autosuspend: +# 0=do not exclude, 1=exclude. +USB_BLACKLIST_PRINTER=1 + +# WWAN devices are excluded from USB autosuspend: +# 0=do not exclude, 1=exclude. +USB_BLACKLIST_WWAN=1 + +# Include listed devices into USB autosuspend even if already excluded +# by the blacklists above (separate with spaces). +# Use lsusb to get the ids. +#USB_WHITELIST="1111:2222 3333:4444" + +# Set to 1 to disable autosuspend before shutdown, 0 to do nothing +# (workaround for USB devices that cause shutdown problems). +#USB_AUTOSUSPEND_DISABLE_ON_SHUTDOWN=1 + +# Restore radio device state (Bluetooth, WiFi, WWAN) from previous shutdown +# on system startup: 0=disable, 1=enable. +# Hint: the parameters DEVICES_TO_DISABLE/ENABLE_ON_STARTUP/SHUTDOWN below +# are ignored when this is enabled! +RESTORE_DEVICE_STATE_ON_STARTUP=0 + +# Radio devices to disable on startup: bluetooth, wifi, wwan. +# Separate multiple devices with spaces. +#DEVICES_TO_DISABLE_ON_STARTUP="bluetooth wifi wwan" + +# Radio devices to enable on startup: bluetooth, wifi, wwan. +# Separate multiple devices with spaces. +#DEVICES_TO_ENABLE_ON_STARTUP="wifi" + +# Radio devices to disable on shutdown: bluetooth, wifi, wwan. +# (workaround for devices that are blocking shutdown). +#DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth wifi wwan" + +# Radio devices to enable on shutdown: bluetooth, wifi, wwan. +# (to prevent other operating systems from missing radios). +#DEVICES_TO_ENABLE_ON_SHUTDOWN="wwan" + +# Radio devices to enable on AC: bluetooth, wifi, wwan. +#DEVICES_TO_ENABLE_ON_AC="bluetooth wifi wwan" + +# Radio devices to disable on battery: bluetooth, wifi, wwan. +#DEVICES_TO_DISABLE_ON_BAT="bluetooth wifi wwan" + +# Radio devices to disable on battery when not in use (not connected): +# bluetooth, wifi, wwan. +#DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth wifi wwan" + +# Battery charge thresholds (ThinkPad only, tp-smapi or acpi-call kernel module +# required). Charging starts when the remaining capacity falls below the +# START_CHARGE_THRESH value and stops when exceeding the STOP_CHARGE_THRESH value. +# Main / Internal battery (values in %) +START_CHARGE_THRESH_BAT0=75 +STOP_CHARGE_THRESH_BAT0=80 +# Ultrabay / Slice / Replaceable battery (values in %) +#START_CHARGE_THRESH_BAT1=75 +#STOP_CHARGE_THRESH_BAT1=80 + +# Restore charge thresholds when AC is unplugged: 0=disable, 1=enable. +#RESTORE_THRESHOLDS_ON_BAT=1 + +# ------------------------------------------------------------------------------ +# tlp-rdw - Parameters for the radio device wizard +# Possible devices: bluetooth, wifi, wwan. + +# Hints: +# - Parameters are disabled by default, remove the leading # to enable them +# - Separate multiple radio devices with spaces + +# Radio devices to disable on connect. +#DEVICES_TO_DISABLE_ON_LAN_CONNECT="wifi wwan" +#DEVICES_TO_DISABLE_ON_WIFI_CONNECT="wwan" +#DEVICES_TO_DISABLE_ON_WWAN_CONNECT="wifi" + +# Radio devices to enable on disconnect. +#DEVICES_TO_ENABLE_ON_LAN_DISCONNECT="wifi wwan" +#DEVICES_TO_ENABLE_ON_WIFI_DISCONNECT="" +#DEVICES_TO_ENABLE_ON_WWAN_DISCONNECT="" + +# Radio devices to enable/disable when docked. +#DEVICES_TO_ENABLE_ON_DOCK="" +#DEVICES_TO_DISABLE_ON_DOCK="" + +# Radio devices to enable/disable when undocked. +#DEVICES_TO_ENABLE_ON_UNDOCK="wifi" +#DEVICES_TO_DISABLE_ON_UNDOCK="" diff --git a/buster/etc_files/x200s/etc/tlp b/buster/etc_files/x200s/etc/tlp deleted file mode 100644 index b73846b..0000000 --- a/buster/etc_files/x200s/etc/tlp +++ /dev/null @@ -1,306 +0,0 @@ -# ------------------------------------------------------------------------------ -# tlp - Parameters for power saving -# See full explanation: http://linrunner.de/en/tlp/docs/tlp-configuration.html - -# Hint: some features are disabled by default, remove the leading # to enable -# them. - -# Set to 0 to disable, 1 to enable TLP. -TLP_ENABLE=1 - -# Operation mode when no power supply can be detected: AC, BAT. -# Concerns some desktop and embedded hardware only. -TLP_DEFAULT_MODE=AC - -# Operation mode select: 0=depend on power source, 1=always use TLP_DEFAULT_MODE -# Hint: use in conjunction with TLP_DEFAULT_MODE=BAT for BAT settings on AC. -TLP_PERSISTENT_DEFAULT=0 - -# Seconds laptop mode has to wait after the disk goes idle before doing a sync. -# Non-zero value enables, zero disables laptop mode. -DISK_IDLE_SECS_ON_AC=0 -DISK_IDLE_SECS_ON_BAT=2 - -# Dirty page values (timeouts in secs). -MAX_LOST_WORK_SECS_ON_AC=15 -MAX_LOST_WORK_SECS_ON_BAT=60 - -# Hint: CPU parameters below are disabled by default, remove the leading # -# to enable them, otherwise kernel default values are used. - -# Select a CPU frequency scaling governor. -# Intel Core i processor with intel_pstate driver: -# powersave(*), performance. -# Older hardware with acpi-cpufreq driver: -# ondemand(*), powersave, performance, conservative, schedutil. -# (*) is recommended. -# Hint: use tlp-stat -p to show the active driver and available governors. -# Important: -# powersave for intel_pstate and ondemand for acpi-cpufreq are power -# efficient for *almost all* workloads and therefore kernel and most -# distributions have chosen them as defaults. If you still want to change, -# you should know what you're doing! You *must* disable your distribution's -# governor settings or conflicts will occur. -#CPU_SCALING_GOVERNOR_ON_AC=powersave -#CPU_SCALING_GOVERNOR_ON_BAT=powersave - -# Set the min/max frequency available for the scaling governor. -# Possible values strongly depend on your CPU. For available frequencies see -# the output of tlp-stat -p. -#CPU_SCALING_MIN_FREQ_ON_AC=0 -#CPU_SCALING_MAX_FREQ_ON_AC=0 -#CPU_SCALING_MIN_FREQ_ON_BAT=0 -#CPU_SCALING_MAX_FREQ_ON_BAT=0 - -# Set energy performance hints (HWP) for Intel P-state governor: -# performance, balance_performance, default, balance_power, power -# Values are given in order of increasing power saving. -# Note: Intel Skylake or newer CPU and Kernel >= 4.10 required. -CPU_HWP_ON_AC=balance_performance -CPU_HWP_ON_BAT=balance_power - -# Set Intel P-state performance: 0..100 (%). -# Limit the max/min P-state to control the power dissipation of the CPU. -# Values are stated as a percentage of the available performance. -# Requires an Intel Core i processor with intel_pstate driver. -#CPU_MIN_PERF_ON_AC=0 -#CPU_MAX_PERF_ON_AC=100 -#CPU_MIN_PERF_ON_BAT=0 -#CPU_MAX_PERF_ON_BAT=30 - -# Set the CPU "turbo boost" feature: 0=disable, 1=allow -# Requires an Intel Core i processor. -# Important: -# - This may conflict with your distribution's governor settings -# - A value of 1 does *not* activate boosting, it just allows it -#CPU_BOOST_ON_AC=1 -#CPU_BOOST_ON_BAT=0 - -# Minimize number of used CPU cores/hyper-threads under light load conditions: -# 0=disable, 1=enable. -SCHED_POWERSAVE_ON_AC=0 -SCHED_POWERSAVE_ON_BAT=1 - -# Kernel NMI Watchdog: -# 0=disable (default, saves power), 1=enable (for kernel debugging only). -NMI_WATCHDOG=0 - -# Change CPU voltages aka "undervolting" - Kernel with PHC patch required. -# Frequency voltage pairs are written to: -# /sys/devices/system/cpu/cpu0/cpufreq/phc_controls -# CAUTION: only use this, if you thoroughly understand what you are doing! -#PHC_CONTROLS="F:V F:V F:V F:V" - -# Set CPU performance versus energy savings policy: -# performance, balance-performance, default, balance-power, power. -# Values are given in order of increasing power saving. -# Requires kernel module msr and x86_energy_perf_policy from linux-tools. -ENERGY_PERF_POLICY_ON_AC=performance -ENERGY_PERF_POLICY_ON_BAT=power - -# Disk devices; separate multiple devices with spaces (default: sda). -# Devices can be specified by disk ID also (lookup with: tlp diskid). -DISK_DEVICES="sda sdb" - -# Disk advanced power management level: 1..254, 255 (max saving, min, off). -# Levels 1..127 may spin down the disk; 255 allowable on most drives. -# Separate values for multiple disks with spaces. Use the special value 'keep' -# to keep the hardware default for the particular disk. -DISK_APM_LEVEL_ON_AC="254 254" -DISK_APM_LEVEL_ON_BAT="128 128" - -# Hard disk spin down timeout: -# 0: spin down disabled -# 1..240: timeouts from 5s to 20min (in units of 5s) -# 241..251: timeouts from 30min to 5.5 hours (in units of 30min) -# See 'man hdparm' for details. -# Separate values for multiple disks with spaces. Use the special value 'keep' -# to keep the hardware default for the particular disk. -#DISK_SPINDOWN_TIMEOUT_ON_AC="0 0" -#DISK_SPINDOWN_TIMEOUT_ON_BAT="0 0" - -# Select IO scheduler for the disk devices: cfq, deadline, noop (Default: cfq). -# Separate values for multiple disks with spaces. Use the special value 'keep' -# to keep the kernel default scheduler for the particular disk. -#DISK_IOSCHED="cfq cfq" - -# AHCI link power management (ALPM) for disk devices: -# min_power, med_power_with_dipm(*), medium_power, max_performance. -# (*) Kernel >= 4.15 required, then recommended. -# Multiple values separated with spaces are tried sequentially until success. -SATA_LINKPWR_ON_AC="med_power_with_dipm max_performance" -SATA_LINKPWR_ON_BAT="med_power_with_dipm min_power" - -# Exclude host devices from AHCI link power management. -# Separate multiple hosts with spaces. -#SATA_LINKPWR_BLACKLIST="host1" - -# Runtime Power Management for AHCI host and disks devices: -# on=disable, auto=enable. -# EXPERIMENTAL ** WARNING: auto will most likely cause system lockups/data loss. -#AHCI_RUNTIME_PM_ON_AC=on -#AHCI_RUNTIME_PM_ON_BAT=on - -# Seconds of inactivity before disk is suspended. -AHCI_RUNTIME_PM_TIMEOUT=15 - -# PCI Express Active State Power Management (PCIe ASPM): -# default, performance, powersave. -PCIE_ASPM_ON_AC=performance -PCIE_ASPM_ON_BAT=powersave - -# Radeon graphics clock speed (profile method): low, mid, high, auto, default; -# auto = mid on BAT, high on AC; default = use hardware defaults. -RADEON_POWER_PROFILE_ON_AC=high -RADEON_POWER_PROFILE_ON_BAT=low - -# Radeon dynamic power management method (DPM): battery, performance. -RADEON_DPM_STATE_ON_AC=performance -RADEON_DPM_STATE_ON_BAT=battery - -# Radeon DPM performance level: auto, low, high; auto is recommended. -RADEON_DPM_PERF_LEVEL_ON_AC=auto -RADEON_DPM_PERF_LEVEL_ON_BAT=auto - -# WiFi power saving mode: on=enable, off=disable; not supported by all adapters. -WIFI_PWR_ON_AC=off -WIFI_PWR_ON_BAT=on - -# Disable wake on LAN: Y/N. -WOL_DISABLE=Y - -# Enable audio power saving for Intel HDA, AC97 devices (timeout in secs). -# A value of 0 disables, >=1 enables power saving (recommended: 1). -SOUND_POWER_SAVE_ON_AC=0 -SOUND_POWER_SAVE_ON_BAT=1 - -# Disable controller too (HDA only): Y/N. -SOUND_POWER_SAVE_CONTROLLER=Y - -# Power off optical drive in UltraBay/MediaBay: 0=disable, 1=enable. -# Drive can be powered on again by releasing (and reinserting) the eject lever -# or by pressing the disc eject button on newer models. -# Note: an UltraBay/MediaBay hard disk is never powered off. -BAY_POWEROFF_ON_AC=0 -BAY_POWEROFF_ON_BAT=0 -# Optical drive device to power off (default sr0). -BAY_DEVICE="sr0" - -# Runtime Power Management for PCI(e) bus devices: on=disable, auto=enable. -RUNTIME_PM_ON_AC=on -RUNTIME_PM_ON_BAT=auto - -# Exclude PCI(e) device adresses the following list from Runtime PM -# (separate with spaces). Use lspci to get the adresses (1st column). -#RUNTIME_PM_BLACKLIST="bb:dd.f 11:22.3 44:55.6" - -# Exclude PCI(e) devices assigned to the listed drivers from Runtime PM. -# Default when unconfigured is "amdgpu nouveau nvidia radeon" which -# prevents accidential power-on of dGPU in hybrid graphics setups. -# Use "" to disable the feature completely. -# Separate multiple drivers with spaces. -#RUNTIME_PM_DRIVER_BLACKLIST="amdgpu nouveau nvidia radeon" - -# Set to 0 to disable, 1 to enable USB autosuspend feature. -USB_AUTOSUSPEND=1 - -# Exclude listed devices from USB autosuspend (separate with spaces). -# Use lsusb to get the ids. -# Note: input devices (usbhid) are excluded automatically -#USB_BLACKLIST="1111:2222 3333:4444" - -# Bluetooth devices are excluded from USB autosuspend: -# 0=do not exclude, 1=exclude. -USB_BLACKLIST_BTUSB=0 - -# Phone devices are excluded from USB autosuspend: -# 0=do not exclude, 1=exclude (enable charging). -USB_BLACKLIST_PHONE=0 - -# Printers are excluded from USB autosuspend: -# 0=do not exclude, 1=exclude. -USB_BLACKLIST_PRINTER=1 - -# WWAN devices are excluded from USB autosuspend: -# 0=do not exclude, 1=exclude. -USB_BLACKLIST_WWAN=1 - -# Include listed devices into USB autosuspend even if already excluded -# by the blacklists above (separate with spaces). -# Use lsusb to get the ids. -#USB_WHITELIST="1111:2222 3333:4444" - -# Set to 1 to disable autosuspend before shutdown, 0 to do nothing -# (workaround for USB devices that cause shutdown problems). -#USB_AUTOSUSPEND_DISABLE_ON_SHUTDOWN=1 - -# Restore radio device state (Bluetooth, WiFi, WWAN) from previous shutdown -# on system startup: 0=disable, 1=enable. -# Hint: the parameters DEVICES_TO_DISABLE/ENABLE_ON_STARTUP/SHUTDOWN below -# are ignored when this is enabled! -RESTORE_DEVICE_STATE_ON_STARTUP=0 - -# Radio devices to disable on startup: bluetooth, wifi, wwan. -# Separate multiple devices with spaces. -#DEVICES_TO_DISABLE_ON_STARTUP="bluetooth wifi wwan" - -# Radio devices to enable on startup: bluetooth, wifi, wwan. -# Separate multiple devices with spaces. -#DEVICES_TO_ENABLE_ON_STARTUP="wifi" - -# Radio devices to disable on shutdown: bluetooth, wifi, wwan. -# (workaround for devices that are blocking shutdown). -#DEVICES_TO_DISABLE_ON_SHUTDOWN="bluetooth wifi wwan" - -# Radio devices to enable on shutdown: bluetooth, wifi, wwan. -# (to prevent other operating systems from missing radios). -#DEVICES_TO_ENABLE_ON_SHUTDOWN="wwan" - -# Radio devices to enable on AC: bluetooth, wifi, wwan. -#DEVICES_TO_ENABLE_ON_AC="bluetooth wifi wwan" - -# Radio devices to disable on battery: bluetooth, wifi, wwan. -#DEVICES_TO_DISABLE_ON_BAT="bluetooth wifi wwan" - -# Radio devices to disable on battery when not in use (not connected): -# bluetooth, wifi, wwan. -#DEVICES_TO_DISABLE_ON_BAT_NOT_IN_USE="bluetooth wifi wwan" - -# Battery charge thresholds (ThinkPad only, tp-smapi or acpi-call kernel module -# required). Charging starts when the remaining capacity falls below the -# START_CHARGE_THRESH value and stops when exceeding the STOP_CHARGE_THRESH value. -# Main / Internal battery (values in %) -START_CHARGE_THRESH_BAT0=75 -STOP_CHARGE_THRESH_BAT0=80 -# Ultrabay / Slice / Replaceable battery (values in %) -#START_CHARGE_THRESH_BAT1=75 -#STOP_CHARGE_THRESH_BAT1=80 - -# Restore charge thresholds when AC is unplugged: 0=disable, 1=enable. -#RESTORE_THRESHOLDS_ON_BAT=1 - -# ------------------------------------------------------------------------------ -# tlp-rdw - Parameters for the radio device wizard -# Possible devices: bluetooth, wifi, wwan. - -# Hints: -# - Parameters are disabled by default, remove the leading # to enable them -# - Separate multiple radio devices with spaces - -# Radio devices to disable on connect. -#DEVICES_TO_DISABLE_ON_LAN_CONNECT="wifi wwan" -#DEVICES_TO_DISABLE_ON_WIFI_CONNECT="wwan" -#DEVICES_TO_DISABLE_ON_WWAN_CONNECT="wifi" - -# Radio devices to enable on disconnect. -#DEVICES_TO_ENABLE_ON_LAN_DISCONNECT="wifi wwan" -#DEVICES_TO_ENABLE_ON_WIFI_DISCONNECT="" -#DEVICES_TO_ENABLE_ON_WWAN_DISCONNECT="" - -# Radio devices to enable/disable when docked. -#DEVICES_TO_ENABLE_ON_DOCK="" -#DEVICES_TO_DISABLE_ON_DOCK="" - -# Radio devices to enable/disable when undocked. -#DEVICES_TO_ENABLE_ON_UNDOCK="wifi" -#DEVICES_TO_DISABLE_ON_UNDOCK=""